WiFi routers have gained much popularity with the advent of wireless internet. They are assigned the task of taking the WiFi signals emitted by a modem and transmitting them in hard-to-wire areas of the house. But, there are times when a router owner resets it due to some reasons. Have you also performed a factory default reset on your router? Well, you might be having a smoother internet experience now. But, it seems that you are worried. Is your WiFi router not connecting to the internet followed by the reset process? That can be quite disappointing as it can stop you from accessing IP addresses like 192.168.11.1. But, then worry not! In this post, we have mentioned some hacks that can be adopted to get the problem fixed easily.
Fixed: Router Can’t Connect To Internet after Reset
The troubleshooting process will become a lot easier if you attempt to restart the WiFi router first. The reason being, it will help you address technical glitches. So, power down the wireless router and remove it from its respective power outlet. After that, wait for at least 30 minutes and follow the same procedure in the reverse order. If your router gets connected to the internet, then you do not need to go through any of the following troubleshooting tips.
- Connect the WiFi Devices Properly
During the reset process, you might have disconnected the wireless router from the modem. In other words, you have disengaged the Ethernet cable joining both networking devices. Therefore, there are chances that after completing the reset process you might have forgotten to connect them or have connected them improperly.
Whatever the scenario might be, you are required to make amends. First of all, join both devices again using the LAN and Internet ports. Once done, check the connection at the end of the ports. If it is not finger-tight, then tighten it. However, you need to make sure that the Ethernet cable that has been employed for connecting the router and modem is non-damaged.
- Check the Router’s Placement
Since the router might have been displaced to execute the reset process, there is a probability that you have placed it somewhere else. Especially, at a location that is far from the main modem. So, consider reducing the distance separating both devices. But, make sure that you do not place them too close. If you go for this approach, then know that it can result in a clash of WiFi signals of both devices.
Apart from the distance separating the router and modem, you must check the router’s surroundings. The router must not be placed close to televisions, microwave ovens, baby monitors, Bluetooth speakers, treadmills, etc. Apart from this, reflexive surfaces like mirrors, glasses, lenses, etc. must be kept away from the wireless router. Such things bounce the router’s signals resulting in chaos. Since water is a good conductor of electricity, objects carrying water have a tendency to absorb the electromagnetic signals emitted by the router. With that said, such objects must also be placed away from your WiFi router.
- Go for 30-30-30 Reset
Tried both the aforementioned hacks, but still, your router cannot connect to the internet? Well, that might be happening because you haven’t reset your router properly. Therefore, you are left with the only option of resetting the router again. Find the Reset button on your right away and press it very carefully with the help of a paper clip or an oil pin. The button needs to be pressed for at least 30 seconds.
Just in case your WiFi router still cannot connect to the internet, then performing a 30-30-30 reset is recommended. Do you know what the process is? Well, you only have to execute the WiFi router reset process 3 times. The duration for which the button on the router needs to be pressed is 30 seconds. Be very sure that you are careful during the reset process. Once your router resets, it will be all set to get connected to the internet. The only thing you need to do is set it up via the 192.168.10.1/ URL.
Summing Up
It can be very frustrating when the WiFi router does not get connected to the internet after the reset process. We hope that once you are done following the aforementioned techniques, you will be able to get rid of the issue.
However, to make your router connect to the internet again followed by the reset process, connect it to the modem using a LAN cable and access the default IP of the router on a computer. The computer in use must be connected to the router’s network. After you are done accessing the IP, log in to the router using the default login credentials and set it up using the instructions that show up on the computer screen. Thanks for reading the post!