A Rockspace Extender can be a real lifesaver when it comes to extending your WiFi coverage. But, sometimes you might run into issues, like the WPS light blinking unexpectedly. But fear not! In this guide, we’ll walk you through the simple steps to fix the blinking WPS light on your Rockspace Extender. So, keep reading!

Before we proceed further we would like to tell you about the meaning of the WPS light on the Rockspace extender. By knowing the meaning you will understand the situation and will easily be able to fix it from its roots.

Why Rockspace Extender Blink WPS Light?

The WPS (Wi-Fi Protected Setup) light on your Rockspace Extender blinks to indicate that there’s a problem with the connection. It’s like a little warning signal, but fixing it won’t require a tech guru.

Solutions for Rockspace Extender Blinking WPS Light

Solution 1: Check the Basics

First, let’s make sure everything’s properly plugged in. Check if your extender is connected to a power source and if it’s placed within the optimal range of your main router. Sometimes, a simple placement adjustment can do wonders.

Solution 2: Restart Your Extender

Just like giving your computer a restart can fix issues, the same applies to your extender. By doing this you will fix the minor bugs and remove the temporary hiccups from the device that occur due to over-usage. You can do this by turning it off, waiting for about 10 seconds, and then turning it back on. This can often solve minor connectivity hiccups.

Solution 3: Reconnect WPS

If the light is still blinking, it’s time to reconnect using the WPS method. Here’s what you need to do:

  • Press the WPS button on your main router. This is usually a physical button, but it can also be accessed through the router’s web interface.

  • Within 2 minutes, press the WPS button on your Rockspace Extender.

  • Wait for a few minutes until the WPS light stops blinking and becomes steady. This indicates a successful connection. If it doesn’t become steady, proceed to the next step.

Solution 4: Update the Firmware

Now you should check the firmware version of your device. Maybe it runs on its outdated version. You can do this by accessing the Http://192.168.0.254 default IP address of the extender.

  • Connect to the extender’s WiFi network.

  • Open the web browser and enter the default IP (e.g., Http://192.168.0.254).

  • Log in using default credentials (admin/admin).

  • Find “Firmware Update” or a similar section.

  • Click “Check for Updates” to scan for new firmware.

  • Download and install the update.

  • Allow the extender to reboot if prompted.

  • Log back in to verify the updated firmware version.

In this way, you can update your device. Once the device is updated you will get your extender normal.

Solution 5: Check the WPS Button

It is seen that sometimes users damage the button and break the button mistakenly. So, there is a chance that the WPS button of your device is broken. Check the WPS button to ensure it is damaged-free or not. If you see the button is broken and needs to be changed, then contact customer care if your device is under warranty.

Solution 6: Reset Extender

If none of the above steps work, you can try resetting your Rockspace Extender. There’s usually a small reset button that you can press with a paperclip. Keep in mind that this will erase any custom settings you’ve configured.

Once the device is reset you need to reconfigure it to use the internet. You can install your device by manual method. If you are unaware of the steps that follow the below-given steps:

Re-Install Rockspace Extender

If the WPS light is still blinking, don’t worry. We can manually configure the extender using a browser:

  • Connect your computer to the extender’s network. This might look like “Rockspace_ext.

  • Open a web browser (like Chrome, Firefox, or Safari) and enter “http://re.rockspace.local” or the IP address “192.168.0.254” in the address bar.

  • Follow the on-screen instructions to set up your extender. You might need your main router’s WiFi password during this process.

  • Once the configuration is done, the WPS light should become steady.

Conclusion

Dealing with a blinking WPS light on your Rockspace Extender might seem daunting, but with these easy steps, you can get your Wi-Fi back on track without needing a tech degree.

By john

Leave a Reply

Your email address will not be published. Required fields are marked *